Media converters interconnect different cable types-twisted pair, fiber, and Thin or thick coax—within an existing network. They are often used to connect newer 100-Mbps, Gigabit Ethernet, or ATM equipment to existing networks, which are generally 10BASE-T, 100BASE-T, or a mixture of both. They can also be used in pairs to insert a fiber segment into copper networks to increase cabling distances and enhance immunity to electromagnetic interference (EMI).

Media converters offer an inexpensive alternative to repeaters. They don’t retime the signal or add the signal propagation delays like full repeaters, so they don’t increase the repeater hop count of existing networks. You can use media converters in many applications, but you can’t use them to replace a repeater in cases where you’ve reached the maximum cable distance or the maximum number of devices on a network segment.

Media converters are available in standalone models that convert between two different media types and in chassis-based models that connect many different media types in a single housing.

Rent an apartment

Standalone converters convert between two media. But, like a small apartment, they can be outgrown. Consider your current and future applications before selecting a media converter. Standalone converters are available in many configurations, including 10BASE-T to multimode or single-mode fiber, 10BASE-T to Thin coax (ThinNet), 10BASE-T to thick coax (standard Ethernet), CDDI to FDDI, and Thin coax to fiber. 100BASE-T and 100BASE-FX models that connect UTP to single- or multimode fiber are also available.

With the development of ATM (asynchronous transfer mode) and Gigabit Ethernet (1000 Mbps), media converters for these higher speeds and protocols have been created to make the transition to these networks easier. 10BASE-T to coax models convert to either ThinNet with a BNC connector or to standard Ethernet with an AUI connector. 10BASE-T to 10BASE-T models are used to double the 100-meter (328-ft.) distance limitation of a 10BASE-T connection. Many of these converters have an uplink or a crossover switch that enables you to connect to either a 10BASE-T workstation or a 10BASE-T hub without a cross-pinned cable.

100BASE-TX twisted pair to 100BASE-FX fiber models also come in many configurations. Some support either half- or full-duplex operation; some support both. The fiber ports work multimode fiber with ST® or SC connectors or single-mode fiber with SC connectors. ATM and Gigabit modules commonly have SC or ST connectors.

...or buy a house.

Chassis-based or modular media converters are normally rackmountable and have slots that house media converter modules. Like a well-planned house, the chassis gives you room to grow. These are used when many Ethernet segments of different media types need to be connected in a central location. Modules are available for the same conversions performed by the standalone converters, and 10BASE-T, 100BASE-TX, 100BASE-FX, ATM, and Gigabit modules may also be mixed. If a switch is used in conjunction with the media converter, all the networks can communicate with each other.

The news on bandwidth
The need for increased bandwidth never ceases—the more you have, the more you need. Applications keep getting more complex, and files keep getting bulkier. It won’t be long before you need to increase the speed of your network.

Don’t worry. Black Box experts are ready 24 hours a day to answer your questions. When you click on “Talk to a Tech,” you’ll be talking to a trained expert in seconds. If you need help installing a network, or adding an additional drop, contact us.

Because unshielded twisted-pair UTP cable is by far the most common networking cable, let’s take a brief look at where UTP is headed.

The limits of Category 5
Category 5 (CAT5) cabling is good, solid cable for 100-Mbps LANs. The Category 5 standard has been around since 1991, so it’s well established. You’ll find existing Category 5 installations everywhere. What can Category 5 cable do, and what can’t it do?

If you still have a lot of 10-Mbps equipment, CAT5 cabling will serve your needs. It also handles 100-Mbps Fast Ethernet transmissions very well.

But if you’re running up against the performance limits of a 100-Mbps network, you’ll probably want to upgrade at least parts of your system fairly soon to Category 5e (CAT5e) or higher.

Category 5e: the improved Category 5
Category 5e, also known as Enhanced Category 5, or CAT5e, was ratified in 1999. It’s an incremental improvement designed to enable cabling to support full-duplex Fast Ethernet operation and Gigabit Ethernet.

The main differences between CAT5 and CAT5e can be found in the specifications. The performance requirements have been raised slightly in the new standard.

CAT5e has stricter specifications for Power Sum Equal-Level Far-End Crosstalk (PS-ELFEXT), Near-End Crosstalk (NEXT), Attenuation, and Return Loss (RL) than those for CAT5. Like CAT5, CAT5e is a 100-MHz standard, but it has the capacity to handle bandwidth superior to that of CAT5. With these improvements, you can expect problem-free, full-duplex, 4-pair Ethernet transmissions over your CAT5e UTP.

Category 6
The next level in the cabling hierarchy is Category 6 (CAT6) (ANSI/TIA/EIA-568-B.2-1), which was ratified by the TIA/EIA in June 2002. CAT6 provides higher performance than CAT5e and features more stringent specifications for crosstalk and system noise.

The quality of the data transmission depends upon the performance of all the components of the channel. So to transmit according to CAT6 specs, the jacks, patch cables, patch panels, cross-connects, and cabling must all meet CAT6 standards. (The channel includes everything from the wallplate to the wiring closet.) The CAT6 components are tested individually, and they are also tested together for performance. In addition, the standard calls for generic system performance so that CAT6 components from any vendor can be used in the channel.

CAT6 channel transmission requirements should result in a Power-Sum Attenuation-to-Crosstalk Ratio (PS-ACR) that’s greater than or equal to zero at 200 MHz.

In addition, all CAT6 components must be backward compatible with CAT5e, CAT5, and CAT3. If different category components are used with CAT6 components, then the channel will achieve the transmission performance of the lower category. For instance, if CAT6 cable is used with CAT5e jacks, the channel will perform at a CAT5e level.

Industry standards
The advantage of sticking to the industry standards is the knowledge that your cabling will be compatible with standards applications. But the standards are always being improved upon, and it takes time to ratify a new standard. Often, as with CAT6, the final standard may be different from the proposed standard. For the latest information, contact our FREE Tech Support.

Twisted-Pair Cable Specifications Comparison
Frequency — CAT5, CAT5e: 100 MHz;
CAT6: 250 MHz;
CAT7 (Proposed): 600 MHz
Attenuation (min. at 100 MHz) — CAT5, CAT5e: 22 dB;
CAT6: 19.8 dB;
CAT7 (Proposed): 20.8 dB
Characteristic Impedance — All: 100 ohms ± 15%
NEXT (min. at 100 MHz) — CAT5: 32.3 dB;
CAT5e: 35.3 dB;
CAT6: 44.3 dB;
CAT7 (Proposed): 62.1 dB
PS-NEXT (min. at 100 MHz) — CAT5: no specification;
CAT5e: 32.3 dB;
CAT6: 42.3 dB;
CAT7 (Proposed): 59.1 dB
ELFEXT (min. at 100 MHz) — CAT5: no specification;
CAT5e: 23.8 dB;
CAT6: 27.8 dB;
CAT7 (Proposed): not yet specified
PS-ELFEXT (min. at 100 MHz) — CAT5: no specification;
CAT5e: 20.8 dB;
CAT6: 24.8 dB;
CAT7 (Proposed): not yet specified
Return Loss (min. at 100 MHz) — CAT5: 16 dB;
CAT5e: 20.1 dB;
CAT6: 20.1 dB;
CAT7 (Proposed): 14.1 dB
Delay Skew (max. per 100 m) — CAT5: no specification;
CAT5e: 45 ns:
CAT6: 45 ns;
CAT7 (Proposed): 20 ns