Networking > Media Converters

Media converters transparently convert the incoming electrical signal from one cable type and then transmit it over another type—thick coax to Thin, UTP to fiber, and so on. Traditionally, media converters were purely Layer 1 devices that only converted electrical signals and physical media and didn’t do anything to the data coming through the link.

Today’s media converters, however, are often more advanced Layer 2 Ethernet devices that, like traditional media converters, provide Layer 1 electrical and physical conversion. But, unlike traditional media converters, they also provide Layer 2 services and route Ethernet packets based on MAC address. These media converters are often called media converter switches, switching media converters, or Layer 2 media converters. They enable you to have multiple connections rather than just one simple in-and-out connection. And because they’re switches, they increase network efficiency.

Media converters are often used to connect newer 100-Mbps, Gigabit Ethernet, or ATM equipment to existing networks, which are generally 10BASE-T, 100BASE-T, or a mixture of both. They can also be used in pairs to insert a fiber segment into copper networks to increase cabling distances and enhance immunity to electromagnetic interference.

Rent an apartment…
Media converters are available in standalone models that convert between two different media types and in chassis-based models that house many media converters in a a single chassis.

Standalone models convert between two media. But, like a small apartment, they can be outgrown.

Consider your current and future applications before selecting a media converter. A good way to anticipate future network requirements is to choose media converters that work as standalone devices but can be rackmounted if needed later.

…or buy a house.
Chassis-based or modular media converter systems are normally rackmountable and have slots to house media converter modules. Like a well-planned house, the chassis gives you room to grow. These are used when many Ethernet segments of different media types need to be connected in a central location. Modules are available for the same conversions performed by the standalone converters, and they enable you to mix different media types such as 10BASE-T, 100BASE-TX, 100BASE-FX, ATM, and Gigabit modules. Although enterprise-level chassis-based systems generally have modules that can only be used in a chassis, many midrange systems feature modules that can be used individually or in a chassis.

The number of Ethernet switches and fiber optic segments being added to Ethernet networks keeps increasing. And as long as most Ethernet switches are only available with 10BASE-T and 100BASE-TX interfaces, media converters will remain in demand.

Until now, a failure on the network could go unnoticed. Once a failure was detected, it could take a long time to isolate it, especially if a technician had to be sent to the site. But media converters with SNMP eliminate some of the guesswork.

With SNMP, the IS manager can detect a failure, isolate it to a specific port, and determine what hardware is required to repair it. A technician can then be sent directly to the right place to fix faulty hardware or repair a broken cable.

SNMP enables you to set up alarms or traps when a link is down. You can turn features on and off from a central terminal, so there’s no need to leave your desk. You can also monitor power supplies and replace them without interrupting service. SNMP management reduces the time and money it takes to get your network up and running again. The users on your network will notice—and appreciate—the improved service and reliability.

SNMP (Simple Network Management Protocol) management is the standard for LAN management, particularly in mission-critical applications. The standard is controlled by the Internet Engineering Task Force (IETF). It was designed to manage network configuration, performance, faults, accounting, and security.

An SNMP agent must be present at the device level (a router or a hub, for example), either built into the unit or as a proxy agent, and is accessed through a remote terminal. SNMP does not follow a polling protocol. It waits to receive data from the remote device or sends data based on operator commands.

By using one common set of standards, SNMP enables network administrators to manage, monitor, and control their SNMP-compliant network equipment with one management system and from one management station. If a network device goes down, it|s possible to both pinpoint and troubleshoot the problem more efficiently. And a network administrator isn’t limited to equipment from just one vendor when using an SNMP program.

Media converters interconnect different cable types such as twisted pair, fiber, and coax within an existing network. They are often used to connect newer Ethernet equipment to legacy cabling. They can also be used in pairs to insert a fiber segment into copper networks to increase cabling distances and enhance immunity to electromagnetic interference (EMI).

Traditional media converters are purely Layer 1 devices that only convert electrical signals and physical media. They don’t do anything to the data coming through the link so they’re totally transparent to data. These converters have two ports—one port for each media type. Layer 1 media converters only operate at one speed and cannot, for instance, support both 10-Mbps and 100-Mbps Ethernet.

Some media converters are more advanced Layer 2 Ethernet devices that, like traditional media converters, provide Layer 1 electrical and physical conversion. But, unlike traditional media converters, they also provide Layer 2 services—in other words, they’re really switches. This kind of media converter often has more than two ports, enabling you to, for instance, extend two or more copper links across a single fiber link. They also often feature autosensing ports on the copper side, making them useful for linking segments operating at different speeds.

Media converters are available in standalone models that convert between two different media types and in chassis-based models that connect many different media types in a single housing.

Rent an apartment

Standalone converters convert between two media. But, like a small apartment, they can be outgrown. Consider your current and future applications before selecting a media converter. Standalone converters are available in many configurations, including 10BASE-T to multimode or single-mode fiber, 10BASE-T to Thin coax (ThinNet), 10BASE-T to thick coax (standard Ethernet), CDDI to FDDI, and Thin coax to fiber. 100BASE-T and 100BASE-FX models that connect UTP to single- or multimode fiber are also available. With the development of Gigabit Ethernet (1000 Mbps), media converters have been created to make the transition to high-speed networks easier.

...or buy a house.

Chassis-based or modular media converters are normally rackmountable and have slots that house media converter modules. Like a well-planned house, the chassis gives you room to grow. These are used when many Ethernet segments of different media types need to be connected in a central location. Modules are available for the same conversions performed by the standalone converters, and 10BASE-T, 100BASE-TX, 100BASE-FX, and Gigabit modules may also be mixed.