Infrastructure Hardware

The BNC (Bayonet-Neill-Concelman) connector is the most commonly used coax connector. This large ”bayonet“ connector features a slotted outer conductor and an inner plastic dielectric, and it offers easy connection and disconnection. After insertion, the plug is turned, tightening the pins in the socket. It is widely used in video and Radio Frequency (RF) applications up to 2.4 GHz. It is also common in 10BASE2 Ethernet networks, on cable interconnections, network cards, and test equipment.

The TNC connector is a threaded version of the BNC connector. It works in frequencies up to 12 GHz. It‘s commonly used in cellular telephone RF/antenna applications.

The N connector is a larger, threaded connector that was designed in the 1940s for military systems operating at less than 5 GHz. In the 1960s, improvements raised performance to 12 GHz. The connector features an internal gasket and is hand tightened. It is common on 2.4-GHz antennas.

The UHF connector looks like a coarse-threaded, big center-conductor version of the N connector. It was developed in the 1930s. It is suitable for use up to 200–300 MHz and generally offers nonconstant impedance.

The F connector is most often used in cable and satellite TV and antenna applications; and it performs well at high frequencies. The connector has a 3/8–32 coupling thread. Some F connectors are also available in a screw-on style.

The SMA (Subminiature A) connector is one of the most common RF/microwave connectors. This small, threaded connector is used on small cables that won’t be connected and disconnected often. It’s designed for use to 12.4 GHz, but works well at 18, and sometimes even up to 24 GHz. This connector is often used in avionics, radar, and microwave communications.

The SMC (Subminiature C) connector is a small, screw-on version of the SMA. It uses a 10–32 threaded interface and can be used in frequencies up to 10 GHz. This connector is used primarily in microwave environments.

The SMB (Subminiature B) connector is a small version of the SMC connector. It was developed in the 1960s and features a snap-on coupling for fast connections. It features a self-centering outer spring and overlapping dielectric. It is rated from 2–4 GHZ, but can possibly work up to 10 GHz.

The MCX (Micro Coax) connector is a coax RF connector developed in the 1980s. It has a snap-on interface and uses the same inner contact and insulator as the SMB connector but is 30% smaller. It can be used in broadband applications up to 6 GHz.

CAT6a is a 10-Gigabit Ethernet (10-GbE) over copper proposal to the CAT6 standard. The IEEE published a draft standard (Std 802.3an) in October 2004. The draft calls for 10-Gigabit data transmission over a 4-connector twisted-pair copper cable for a distance of 100 meters on Class F or Class E-augmented copper cabling. Class E cabling requires a line-encoding scheme (PAM 12) and electronics to achieve the 10-Gbps transmission for 100 meters. Current CAT6 cabling systems may support 10-Gigabit Ethernet over limited distances.

The draft extends CAT6 electrical specifications from 250 MHz to 500 MHz. It also proposes a new measurement: Power-Sum Alien Crosstalk to 500 MHz. Alien Crosstalk (ANEXT) is a coupled signal in a disturbed pair arising from a signal in a neighboring cable.
To virtually eliminate the problem of ANEXT, CAT6a F/UTP cable can be used. The F indicates an outer foil shield. This cable is also a good choice when security is an issue because it doesn’t emit signals. In addition, CAT6a F/UTP cable works well in noisy environments with a lot of EMI. Installation is simpler, too, because the cable’s construction makes it easier to pull and more resilient. The cable also has a smaller diameter so you can run more cables in a conduit.