External

Small Computer Systems Interface (SCSI), pronounced “scuzzy,” has been the dominant technology used to connect computers and high-speed peripherals since the 1980s. SCSI technology is constantly evolving to accommodate increased bandwidth needs. One of the more recent developments is Ultra2 SCSI.

Because Ultra2 SCSI is backward compatible, it works with all legacy equipment. Ultra2 doubles the possible bandwidth on the bus from 40 to 80 MBps! Just as importantly, Ultra2 supports distances up to 12 meters (39.3 ft.) for a multiple-device configuration. Ultra2 uses Low-voltage Differential (LVD) techniques to transfer data at faster rates with fewer errors. Don’t confuse Ultra2 with LVD. Ultra2 is a data-transfer method; LVD is the signaling technique used to transfer the data.

Cables are very important when designing or upgrading a system to take advantage of Ultra2 SCSI. Cables and connectors must be of high quality and they should come from a reputable manufacturer to prevent crosstalk and minimize signal radiation. BLACK BOX® Ultra2 LVD cables are constructed of the finest-quality components to provide your system with the maximum protection and highest possible data-transfer rates.

1. Quality. Your system’s performance depends on the quality of your SCSI cables. Without high-quality cables specifically designed for SCSI applications, you could be jeopardizing your SCSI lifeline. Inferior cables, adapters, and terminators can cause random errors, data corruption, or even a system crash! Black Box® SCSI Cables and components are the absolute best-quality products. And they’re guaranteed for life.

2. Length. For peak network performance, make sure your cables are the right length. As cable runs get longer, signals weaken and are more susceptible to noise. Always use the shortest cable for the task. And stay within the SCSI-1 and SCSI-2 standards of six meters or three meters for Fast SCSI. Remember, this is the total length of the bus, including all internal and external cables.

There are standards…and there are standards applied in real-world applications. This Black Box Explains illustrates how SCSI is interpreted by many SCSI manufacturers. Think of these as common SCSI connector types, not as firm SCSI specifications. Notice, for instance, there’s a SCSI-5, which isn’t listed among the other approved and proposed specifications. However, for advanced SCSI multiport applications, SCSI-5 is often the connector of choice.

SCSI-1
Supports transfer rates up to 5 MBps and seven SCSI devices on an 8-bit bus. The most common connector is the Centronics® 50 or a DB50. A Micro Ribbon 50 is also used for internal connections. SCSI-1 equipment, such as controllers, can also have Burndy 60 or 68 connectors.

SCSI-2
SCSI-2 introduced optional 16- and 32-bit buses called “Wide SCSI.“ Transfer rate is normally 10 MBps but SCSI-2 can go up to 40 MBps with Wide and Fast SCSI. SCSI-2 usually features a Micro D 50-pin connector with thumbclips. It’s also known as Mini 50 or Micro DB50. A Micro Ribbon 60 connector may also be used for internal connections.

SCSI-3
Found in many high-end systems, SCSI-3 commonly uses a Micro D 68-pin connector with thumbscrews. It’s also known as Mini 68. The most common bus width is 16 bits with transfer rates of 20 MBps.

SCSI-5
SCSI-5 is also called a Very High-Density Connector Interface (VHDCI) or 0.8-mm connector. It’s similar to the SCSI-3 MD68 connector in that it has 68 pins, but it has a much smaller footprint. SCSI-5 is designed for SCSI-5, next-generation SCSI connections. Manufacturers are integrating this 0.8-mm design into controller cards. It’s also the connector of choice for advanced SCSI multiport applications. Up to four channels can be accommodated in one card slot. Connections are easier where space is limited.