Product Data Sheets (pdf)...Wire Marker Tape
Product Data Sheets (pdf)...Fiber Connector Tool Kit
Product Data Sheets (pdf)...Firestop Pillows
Black Box Explains...Firestop Basics
Product Data Sheets (pdf)...Tool Kits
Product Data Sheets (pdf)...Fluorescent and Flexible-Neck Lights
Product Data Sheets (pdf)...Insulated Terminal Kit
Product Data Sheets (pdf)...CAT5e Termination Kit CAT5e Installation Kit
Cables pose a fire risk.
Most cables are constructed with standard polymer jackets, which are combustible. Copper and aluminum are the most common metals used as conductors. Unfortunately, theyre good conductors... more/see it nowof heat. The conductors can spread a fire by igniting surrounding flammable materials, such as the cable jacket. Then the jacket burns away, the conductors melt together, and the size of the cable bundle shrinks and causes gaps to develop within the cabling opening.
Successful firestop planning.
A well-designed cabling system requires careful planning to meet the needs of future cabling requirements and fire protection. Most people tend to underestimate the size of the openings required for cabling and often forget about future expansion. When planning on how large to make the opening to run your cable, you must consider the diameter of the cable itself, how much room you need for firestopping materials, and whether youll be adding more cables in the future.
Permanent vs. retrofittable cabling.
There are two basic types of cabling systems: permanent and retrofittable. Permanent cabling systems, such as electrical cables, do not change. But most cabling systems, such as data and voice, have to accommodate moves, adds, and changes so they need to be retrofittable. You use different firestops with each system.
In permanent installations, a sealant is used in and around the cables. This is also appropriate for external areas, including conduits and sleeves.
In retrofittable systems, firestops need to be removed and reinstalled easily as cable needs change. Common firestops include pillows, putty, and fire-rated pathways. These products are packed in and around a cable bundle rather than being injected the way sealant is. The product to use often depends on the size of the cable opening and the frequency of changes.
Passive vs. intumescent firestopping.
There are two basic types of materials used in firestopping: Passive firestopping uses nonintumescent materials, which draw heat away or insulate the cables. Passive materials include mortars, silicone sealants, foam, and grout. Cabling runs with passive firestopping are generally thicker and are more limited in the types of cables they can protect.
Intumescent materials expand when exposed to heat or fire and compensate for the loss of mass in cable bundles. Theyre a good choice for sealing and surrounding cable holes and runs. collapse
Black Box Explains...Cable termination.
Product Data Sheets (pdf)...AntiStatic Service Kit and Wrist Strap
Carefully remove the jacketing from the cable and expose one inch of the insulated wire conductors. Do not remove any insulation from the conductors. When the... more/see it nowRJ-45 connector is crimped, the contacts inside will pierce the conductor insulation.
Untwist the wires to within 1/8" of the jacket. Arrange the wires according to the cable spec (568B in this case). Flatten and align the wires. Make one straight cut across all the conductors, removing approximately 1/2" to ensure the ends are of equal length.
Slide the wires into a connector. The cable jacket should extend into the connector about 1/4" for strain relief. Orient the wires so connector Pin 1 aligns with cable Pin 1, etc. Hold the connector in front of you. With the locking tab down, Pin 1 is on the far left.
Insert the connector into a crimp tool. Make sure you’re using the proper die. Firmly squeeze the handles. They’ll lock in a ratcheting action. A final click indicates the connector is firmly latched.
Check your work using a continuity tester or cable certifier rated for the cable standard you’re installing. Your tester should be able to check for shorts, opens, or miswires.