Black Box Explains...Media converters that are really switches.
A media converter is a device that converts from one media type to another, for instance, from twisted pair to fiber to take advantage of fiber’s greater range. A traditional... more/see it nowmedia converter is a two-port Layer 1 device that performs a simple conversion of only the physical interface. It’s transparent to data and doesn't “see” or manipulate data in any way.
An Ethernet switch can also convert one media type to another, but it also creates a separate collision domain for each switch port, so that each packet is routed only to the destination device, rather than around to multiple devices on a network segment. Because switches are “smarter” than traditional media converters, they enable additional features such as multiple ports and copper ports that autosense for speed and duplex.
Switches are beginning to replace traditional 2-port media converters, leading to some fuzziness in terminology. Small 4- or 6-port Ethernet switches are very commonly called media converters. In fact, anytime you see a “Layer 2” media converter or a media converter with more than two ports, it’s really a small Ethernet switch.
48-Port PoE+ Gigabit Managed Switch Eco
Firmware for the LPB2848A (Version v1.58)
Product Data Sheets (pdf)...Palm-Sized Ethernet Switches,
PoE+ Gigabit Managed Switch Eco CLI Guide
CLI Guide for the LPB2810A, LPB2826A, and LPB2848A (Version 1)
LE2700 Series Hardened Managed Modular Switch User Manual
User Manual for the LE2700 Series (LE2700A, LE2710C, LE2711C, LE2720C, LE2721C, LE2731C) (Version 3)
SFP Gigabit Managed Fiber Switch Eco CLI Guide
CLI Guide for the LGB5124A and LGB5128A (Version 1)
Black Box Explains…Media converters that also work as switches.
Media converters transparently convert the incoming electrical signal from one cable type and then transmit it over another type—thick coax to Thin, UTP to fiber, and so on. Traditionally, media... more/see it nowconverters were purely Layer 1 devices that only converted electrical signals and physical media and didn’t do anything to the data coming through the link.
Today’s media converters, however, are often more advanced Layer 2 Ethernet devices that, like traditional media converters, provide Layer 1 electrical and physical conversion. But, unlike traditional media converters, they also provide Layer 2 services and route Ethernet packets based on MAC address. These media converters are often called media converter switches, switching media converters, or Layer 2 media converters. They enable you to have multiple connections rather than just one simple in-and-out connection. And because they’re switches, they increase network efficiency.
Media converters are often used to connect newer 100-Mbps, Gigabit Ethernet, or ATM equipment to existing networks, which are generally 10BASE-T, 100BASE-T, or a mixture of both. They can also be used in pairs to insert a fiber segment into copper networks to increase cabling distances and enhance immunity to electromagnetic interference.
Rent an apartment…
Media converters are available in standalone models that convert between two different media types and in chassis-based models that house many media converters in a a single chassis.
Standalone models convert between two media. But, like a small apartment, they can be outgrown.
Consider your current and future applications before selecting a media converter. A good way to anticipate future network requirements is to choose media converters that work as standalone devices but can be rackmounted if needed later.
…or buy a house.
Chassis-based or modular media converter systems are normally rackmountable and have slots to house media converter modules. Like a well-planned house, the chassis gives you room to grow. These are used when many Ethernet segments of different media types need to be connected in a central location. Modules are available for the same conversions performed by the standalone converters, and they enable you to mix different media types such as 10BASE-T, 100BASE-TX, 100BASE-FX, ATM, and Gigabit modules. Although enterprise-level chassis-based systems generally have modules that can only be used in a chassis, many midrange systems feature modules that can be used individually or in a chassis. collapse
Black Box Explains...Ethernet.
If you have an existing network, there’s a 90% chance it’s Ethernet. If you’re installing a new network, there’s a 98% chance it’s Ethernet—the Ethernet standard is... more/see it nowthe overwhelming favorite network standard today.
Ethernet was developed by Xerox®, DEC®, and Intel® in the mid-1970s as a 10-Mbps (Megabits per second) networking protocol—very fast for its day—operating over a heavy coax cable (Standard Ethernet).
Today, although many networks have migrated to Fast Ethernet (100 Mbps) or even Gigabit Ethernet (1000 Mbps), 10-Mbps Ethernet is still in widespread use and forms the basis of most networks.
Ethernet is defined by international standards, specifically IEEE 802.3. It enables the connection of up to 1024 nodes over coax, twisted-pair, or fiber optic cable. Most new installations today use economical, lightweight cables such as Category 5 unshielded twisted-pair cable and fiber optic cable.
How Ethernet Works
Ethernet signals are transmitted from a station serially, one bit at a time, to every other station on the network.
Ethernet uses a broadcast access method called Carrier Sense Multiple Access/Collision Detection (CSMA/CD) in which every computer on the network hears every transmission, but each computer listens only to transmissions intended for it.
Each computer can send a message anytime it likes without having to wait for network permission. The signal it sends travels to every computer on the network. Every computer hears the message, but only the computer for which the message is intended recognizes it. This computer recognizes the message because the message contains its address. The message also contains the address of the sending computer so the message can be acknowledged.
If two computers send messages at the same moment, a collision occurs, interfering with the signals. A computer can tell if a collision has occurred when it doesn’t hear its own message within a given amount of time. When a collision occurs, each of the colliding computers waits a random amount of time before resending the message.
The process of collision detection and retransmission is handled by the Ethernet adapter itself and doesn’t involve the computer. The process of collision resolution takes only a fraction of a second under most circumstances. Collisions are normal and expected events on an Ethernet network. As more computers are added to the network and the traffic level increases, more collisions occur as part of normal operation. However, if the network gets too crowded, collisions increase to the point where they slow down the network considerably.
Standard (Thick) Ethernet (10BASE5)
Thin Ethernet (ThinNet) (10BASE2)
- Uses thick coax cable with N-type connectors for a backbone and a transceiver cable with 9-pin connectors from the transceiver to the NIC.
- Both ends of each segment should be terminated with a 50-ohm resistor.
- Maximum segment length is 500 meters.
- Maximum total length is 2500 meters.
- Maximum length of transceiver cable is 50 meters.
- Minimum distance between transceivers is 2.5 meters.
- No more than 100 transceiver connections per segment are allowed.
Twisted-Pair Ethernet (10BASE-T)
- Uses "Thin" coax cable.
- The maximum length of one segment is 185 meters.
- The maximum number of segments is five.
- The maximum total length of all segments is 925 meters.
- The minimum distance between T-connectors is 0.5 meters.
- No more than 30 connections per segment are allowed.
- T-connectors must be plugged directly into each device.
Fiber Optic Ethernet (10BASE-FL, FOIRL)
- Uses 22 to 26 AWG unshielded twisted-pair cable (for best results, use Category 4 or 5 unshielded twisted pair).
- The maximum length of one segment is 100 meters.
- Devices are connected to a 10BASE-T hub in a star configuration.
- Devices with standard AUI connectors may be attached via a 10BASE-T transceiver.
- Uses 50-, 62.5-, or 100-micron duplex multimode fiber optic cable (62.5 micron is recommended).
- The maximum length of one 10BASE-FL (the new standard for fiber optic connections) segment is 2 kilometers.
- The maximum length of one FOIRL (the standard that preceded the new 10BASE-FL) segment is 1 kilometer.