Black Box Explains…Media converters that also work as switches.
Media converters transparently convert the incoming electrical signal from one cable type and then transmit it over another type—thick coax to Thin, UTP to fiber, and so on. Traditionally, media... more/see it nowconverters were purely Layer 1 devices that only converted electrical signals and physical media and didn’t do anything to the data coming through the link.
Today’s media converters, however, are often more advanced Layer 2 Ethernet devices that, like traditional media converters, provide Layer 1 electrical and physical conversion. But, unlike traditional media converters, they also provide Layer 2 services and route Ethernet packets based on MAC address. These media converters are often called media converter switches, switching media converters, or Layer 2 media converters. They enable you to have multiple connections rather than just one simple in-and-out connection. And because they’re switches, they increase network efficiency.
Media converters are often used to connect newer 100-Mbps, Gigabit Ethernet, or ATM equipment to existing networks, which are generally 10BASE-T, 100BASE-T, or a mixture of both. They can also be used in pairs to insert a fiber segment into copper networks to increase cabling distances and enhance immunity to electromagnetic interference.
Rent an apartment…
Media converters are available in standalone models that convert between two different media types and in chassis-based models that house many media converters in a a single chassis.
Standalone models convert between two media. But, like a small apartment, they can be outgrown.
Consider your current and future applications before selecting a media converter. A good way to anticipate future network requirements is to choose media converters that work as standalone devices but can be rackmounted if needed later.
…or buy a house.
Chassis-based or modular media converter systems are normally rackmountable and have slots to house media converter modules. Like a well-planned house, the chassis gives you room to grow. These are used when many Ethernet segments of different media types need to be connected in a central location. Modules are available for the same conversions performed by the standalone converters, and they enable you to mix different media types such as 10BASE-T, 100BASE-TX, 100BASE-FX, ATM, and Gigabit modules. Although enterprise-level chassis-based systems generally have modules that can only be used in a chassis, many midrange systems feature modules that can be used individually or in a chassis. collapse
Black Box Explains... SNMP.
SNMP (Simple Network Management Protocol) management is the standard for LAN management, particularly in mission-critical applications. The standard is controlled by the Internet Engineering Task Force (IETF). It was designed... more/see it nowto manage network configuration, performance, faults, accounting, and security.
An SNMP agent must be present at the device level (a router or a hub, for example), either built into the unit or as a proxy agent, and is accessed through a remote terminal. SNMP does not follow a polling protocol. It waits to receive data from the remote device or sends data based on operator commands.
By using one common set of standards, SNMP enables network administrators to manage, monitor, and control their SNMP-compliant network equipment with one management system and from one management station. If a network device goes down, it|s possible to both pinpoint and troubleshoot the problem more efficiently. And a network administrator isnt limited to equipment from just one vendor when using an SNMP program. collapse
Black Box Explains...NEBS Level 3.
Network Equipment Building System (NEBS) standards set requirements for telco equipment. The standards are maintained by Telcordia Technologies, Inc., formerly Bellcore. Bellcore Special Report, SR-3580 defines three distinct functional levels... more/see it nowof NEBS compliance. The third of these levels, NEBS Level 3, is the most stringent, certifying carrier-class equipment intended for long-term use in variable environments.
NEBS Level 3 certifies that a piece of equipment can be safely used in an extreme environment. To become certified at NEBS Level 3, a device must meet strict physical, electrical, and environmental requirements to prove it will operate safely and reliably in extreme conditions. It must pass a series of tests that include extreme heat, humidity, fire, earthquakes (Zone 4), light, and noise. collapse
Black Box Explains...802.3ah.
802.3ah, also called Ethernet in the First Mile (EFM), is a new Ethernet standard designed to compete with standards such as DSL and cable modem in delivering broadband access to... more/see it nowhomes.
The 802.3ah specification covers point-to-point copper, point-to-point fiber, and point-to-multipoint fiber.
Ethernet in the First Mile over Copper (EFMC)
This point-to-point specification for copper wire takes advantage of DSL technology to send Ethernet over one pair of copper wires at 10 Mbps for 750 meters or 2 Mbps for 2700 meters.
Ethernet in the First Mile over Fiber (EFMF)
This point-to-point specification for single-mode, single-strand or single-mode, duplex fiber sends Ethernet at speeds of 100 Mbps or 1 Gbps up to 10 kilometers. It includes an optional extended temperature range from -40 to 185° F (-40 to 85° C) for outdoor use.
Ethernet in the First Mile over Passive Optical Networks (EPON)
This point-to-multipoint specification for fiber uses an optical splitter to divide the Ethernet signal into separate strands that go to individual subscribers. This enables an ISP to link many subscribers to a single uplink fiber without using active components in the field.
802.3ah includes the OAM specification, which provides utilities for monitoring and troubleshooting Ethernet links remotely, a capability vital for carrier-class deployment. OAM protocols address discovery, link monitoring, remote fault signaling, and remote loopback.
OAM is managed in-band but takes up very little bandwidth so network performance is not noticeably affected. OAM itself is not affected by VLANs or port-access restrictions.
Black Box Explains...SFP, SFP+, and XFP transceivers.
SFP, SFP+, and XFP are all terms for a type of transceiver that
plugs into a special port on a switch or other network device to convert the port to... more/see it nowa copper or fiber interface. These compact transceivers replace the older, bulkier GBIC interface. Although these devices are available in copper, their most common use is to add fiber ports. Fiber options include multimode and single-mode fiber in a variety of wavelengths covering distances of up to 120 kilometers (about 75 miles), as well as WDM fiber, which uses two separate wavelengths to both send and receive data on a
single fiber strand.
SFPs support speeds up to 4.25 Gbps and are generally used for Fast Ethernet or Gigabit Ethernet applications. The expanded SFP
standard, SFP+, supports speeds of 10 Gbps or higher over fiber. XFP
is a separate standard that also supports 10-Gbps speeds. The primary difference between SFP+ and the slightly older XFP standard is that SFP+ moves the chip for clock and data recovery into a line card on the host device. This makes an SFP+ smaller than an XFP, enabling greater port density.
Because all these compact transcievers are hot-swappable, there’s no need to shut down a switch to swap out a module—it’s easy to change interfaces on the fly for upgrades and maintenance.
Another characteristic shared by this group of transcievers is that they’re OSI Layer 1 devices—they’re transparent to data and do not examine or alter data in any way. Although they’re primarily used with Ethernet, they’re also compatible with uncommon or legacy standards such as Fibre Channel, ATM, SONET, or Token Ring.
Formats for SFP, SFP+, and XFP transceivers have been standardized by multisource agreements (MSAs) between manufacturers, so
physical dimensions, connectors, and signaling are consistent and
interchangeable. Be aware though that some major manufacturers, notably Cisco, sell network devices with slots that lock out transceivers from other vendors.
Black Box Explains...Why media converters need SNMP.
The number of Ethernet switches and fiber optic segments being added to Ethernet networks keeps increasing. And as long as most Ethernet switches are only available with 10BASE-T and 100BASE-TX... more/see it nowinterfaces, media converters will remain in demand.
Until now, a failure on the network could go unnoticed. Once a failure was detected, it could take a long time to isolate it, especially if a technician had to be sent to the site. But media converters with SNMP eliminate some of the guesswork.
With SNMP, the IS manager can detect a failure, isolate it to a specific port, and determine what hardware is required to repair it. A technician can then be sent directly to the right place to fix faulty hardware or repair a broken cable.
SNMP enables you to set up alarms or traps when a link is down. You can turn features on and off from a central terminal, so theres no need to leave your desk. You can also monitor power supplies and replace them without interrupting service. SNMP management reduces the time and money it takes to get your network up and running again. The users on your network will notice—and appreciate—the improved service and reliability. collapse
Black Box Explains...Media converters.
Media converters interconnect different cable types such as twisted pair, fiber, and coax within an existing network. They are often used to connect newer Ethernet equipment to legacy cabling.... more/see it nowThey can also be used in pairs to insert a fiber segment into copper networks to increase cabling distances and enhance immunity to electromagnetic interference (EMI).
Traditional media converters are purely Layer 1 devices that only convert electrical signals and physical media. They don’t do anything to the data coming through the link so they’re totally transparent to data. These converters have two ports—one port for each media type. Layer 1 media converters only operate at one speed and cannot, for instance, support both 10-Mbps and 100-Mbps Ethernet.
Some media converters are more advanced Layer 2 Ethernet devices that, like traditional media converters, provide Layer 1 electrical and physical conversion. But, unlike traditional media converters, they also provide Layer 2 services—in other words, they’re really switches. This kind of media converter often has more than two ports, enabling you to, for instance, extend two or more copper links across a single fiber link. They also often feature autosensing ports on the copper side, making them useful for linking segments operating at different speeds.
Media converters are available in standalone models that convert between two different media types and in chassis-based models that connect many different media types in a single housing.
Rent an apartment
Standalone converters convert between two media. But, like a small apartment, they can be outgrown. Consider your current and future applications before selecting a media converter. Standalone converters are available in many configurations, including 10BASE-T to multimode or single-mode fiber, 10BASE-T to Thin coax (ThinNet), 10BASE-T to thick coax (standard Ethernet), CDDI to FDDI, and Thin coax to fiber. 100BASE-T and 100BASE-FX models that connect UTP to single- or multimode fiber are also available. With the development of Gigabit Ethernet (1000 Mbps), media converters have been created to make the transition to high-speed networks easier.
...or buy a house.
Chassis-based or modular media converters are normally rackmountable and have slots that house media converter modules. Like a well-planned house, the chassis gives you room to grow. These are used when many Ethernet segments of different media types need to be connected in a central location. Modules are available for the same conversions performed by the standalone converters, and 10BASE-T, 100BASE-TX, 100BASE-FX, and Gigabit modules may also be mixed. collapse