ServSwitch Agility DVI, USB, and Audio Extenders over IP Firmware
Firmware for the ACR1000A, ACR1000A-T, and ACR1000A-R (Version 2.9.21660)
ServSwitch Agility Dual-Head Transmitter with VNC Server
User Manual for the ACR1012A-T (Version 1)
Black Box Explains...Multicasting video over a LAN: Use the right switch.
In KVM extension applications where you want to distribute HD video across a network, you need to understand how it works and what kind of networking equipment to use with... more/see it nowyour extenders.
Think of your network as a river of data with a steady current of data moving smoothly down the channel. All your network users are like tiny tributaries branching off this river, taking only as much water (bandwidth) as they need to process data. When you start to multicast video, data, and audio over the LAN, those streams suddenly become the size of the main river. Each user is then basically flooded with data and it becomes difficult or impossible to do any other tasks. This scenario of sending transmissions to every user on the network is called broadcasting, and it slows down the network to a trickle. There are network protocol methods that alleviate this problem, but it depends on the network switch you use.
Unicast vs. multicasting, and why a typical Layer 2 switch isn’t sufficient.
Unicasting is sending data from one network device to another (point to point); in a typical unicast network, Layer 2 switches easily support these types of communications. But multicasting is transmitting data from one network device to multiple users. When multicasting with Layer 2 switches, all attached devices receive the packets, whether they want them or not. Because a multicast header does NOT have a destination IP address, an average network switch (a Layer 2 switch without supported capabilities) will not know what to do with it. So the switch sends the packet out to every network port on all attached devices. When the client or network interface card (NIC) receives the packet, it analyzes it and discards it if not wanted.
The solution: a Layer 3 switch with IGMPv2 or IGMPv3 and packet forwarding.
Multicasting with Layer 3 switches is much more efficient than with Layer 2 switches because it identifies the multicast packet and sends it only to the intended receivers. A Layer 2 switch sends the multicast packets to every device and, If there are many sources, the network will slow down because of all the traffic. And, without IGMPv2 or IGMPv3 snooping support, the switch can handle only a few devices sending multicasting packets.
Layer 3 switches with IGMP support, however, “know” who wants to receive the multicast packet and who doesn’t. When a receiving device wants to tap into a multicasting stream, it responds to the multicast broadcast with an IGMP report, the equivalent of saying, “I want to connect to this stream.” The report is only sent in the first cycle, initializing the connection between the stream and receiving device. If the device was previously connected to the stream, it sends a grafting request for removing the temporary block on the unicast routing table. The switch can then send the multicast packets to newly connected members of the multicast group.
Then, when a device no longer wants to receive the multicast packets, it sends a pruning request to the IGMP-supported switch, which temporarily removes the device from the multicast group and stream.
Therefore, for multicasting, use routers or Layer 3 switches that support the IGMP protocol. Without this support, your network devices will be receiving so many multicasting packets, they will not be able to communicate with other devices using different protocols, such as FTP. Plus, a feature-rich, IGMP-supported Layer 3 switch gives you the bandwidth control needed to send video from multiple sources over a LAN.
- Application Note...
Ethernet Switches and ServSwitch Agility KVM-over-IP Extension
The important interoperability considerations when choosing Ethernet switches for use with Agility systems. (Version 1)
Black Box Explains...Digital Visual Interface (DVI) connectors.
DVI (Digital Video Interface) is the standard digital interface for transmitting uncompressed high-definition, 1080p video between PCs and monitors and other computer equipment. Because DVI accommodates both analog and digital... more/see it nowinterfaces with a single connector, it is also compatible with the VGA interface. DVI differs from HDMI in that HDMI is more commonly found on HDTVs and consumer electronics.
The DVI standard is based on transition-minimized differential signaling (TMDS). There are two DVI formats: Single-Link and Dual-Link. Single-link cables use one TMDS-165 MHz transmitter and dual-link cables use two. The dual-link cables double the power of the transmission. A single-link cable can transmit a resolution ?of 1920 x 1200 vs. 2560 x 1600 for a dual-link cable.
There are several types of connectors: DVI-D, DVI-I, DVI-A, DFP, and EVC.
DVI-D (digital). This digital-only interface provides a high-quality image and fast transfer rates between a digital video source and monitors. It eliminates analog conversion and improves the display. It can be used when one or both connections are DVI-D.
DVI-I (integrated). This interface supports both digital and analog RGB connections. It can transmit either a digital-to-digital signal or an analog-to-analog signal. It can be used with adapters to enable connectivity to a VGA or DVI-I display or digital connectivity to a DVI-D display. If both connectors are DVI-I, you can use any DVI cable, but DVI-I is recommended.
DVI-A (analog) This interface is used to carry a DVI signal from a computer to an analog VGA device, such as a display. If one connection is DVI and the other is VGA HD15, you need a cable or adapter with both connectors.
DFP (Digital Flat Panel) was an early digital-only connector used on some displays.
EVC (also known as P&D, for Plug & Display), another older connector, handles digital and analog connections.
ServSwitch DTX, Dual-Head, Firmware
Firmware for the DTX5002, DTX5002-T, and DTX5002-R (Version 4.0)
ServSwitch DTX Kit Manual
Manual for the DTX5000, DTX5001 DTX5002, DTX5000-R, DTX5001-R, DTX5002-T, DTX5000-T, DTX5001-T, and DTX5002-R.
ServSwitch DTX Kit, Dual-Head Firmware
Firmware for the DTX5002, DTX5002-T, and DTX5002-R