- Pdf Drawing...
Fiber Optic Connector PDF Drawing
PDF Drawing for the FOT212 and FOT215
Black Box Explains...Fiber connectors.
• The ST® connector, which uses a bayonet locking system, is the most common connector.
• The SC connector features a molded body and a push- pull locking system.
• The FDDI... more/see it nowconnector comes with a 2.5-mm free-floating ferrule and a fixed shroud to minimize light loss.
• The MT-RJ connector, a small-form RJ-style connector, features a molded body and uses cleave-and-leave splicing.
• The LC connector, a small-form factor connector, features a ceramic ferrule and looks like a mini SC connector.
• The VF-45™connector is another small-form factor connector. It uses a unique V-groove design.
• The FC connector is a threaded body connector. Secure it by screwing the connector body to the mating threads. Used in high-vibration environments.
• The MTO/MTP connector is a fiber connector that uses high-fiber-count ribbon cable. Its used in high-density fiber applications.
• The MU connector resembles the larger SC connector. It uses a simple push-pull latching connection and is well suited for high-density applications.
- Pdf Drawing...
Color-Coded Snagless Pre-Plug (Gray) PDF Drawing
PDF Drawing for the FMT721
- Pdf Drawing...
CAT5e Shielded Modular Plug, RJ-45
PDF Drawing for the FMTPES-10PAK, FMTPES-25PAK, FMTPES-50PAK, FMTPES-100PAK, and FMTPES-250PAK
Black Box Explains...Coax connectors.
The BNC (Bayonet-Neill-Concelman) connector is the most commonly used coax connector. This large ”bayonet“ connector features a slotted outer conductor and an inner plastic dielectric, and it offers easy connection... more/see it nowand disconnection. After insertion, the plug is turned, tightening the pins in the socket. It is widely used in video and Radio Frequency (RF) applications up to 2.4 GHz. It is also common in 10BASE2 Ethernet networks, on cable interconnections, network cards, and test equipment.
The TNC connector is a threaded version of the BNC connector. It works in frequencies up to 12 GHz. It‘s commonly used in cellular telephone RF/antenna applications.
The N connector is a larger, threaded connector that was designed in the 1940s for military systems operating at less than 5 GHz. In the 1960s, improvements raised performance to 12 GHz. The connector features an internal gasket and is hand tightened. It is common on 2.4-GHz antennas.
The UHF connector looks like a coarse-threaded, big center-conductor version of the N connector. It was developed in the 1930s. It is suitable for use up to 200–300 MHz and generally offers nonconstant impedance.
The F connector is most often used in cable and satellite TV and antenna applications; and it performs well at high frequencies. The connector has a 3/8–32 coupling thread. Some F connectors are also available in a screw-on style.
The SMA (Subminiature A) connector is one of the most common RF/microwave connectors. This small, threaded connector is used on small cables that won’t be connected and disconnected often. It’s designed for use to 12.4 GHz, but works well at 18, and sometimes even up to 24 GHz. This connector is often used in avionics, radar, and microwave communications.
The SMC (Subminiature C) connector is a small, screw-on version of the SMA. It uses a 10–32 threaded interface and can be used in frequencies up to 10 GHz. This connector is used primarily in microwave environments.
The SMB (Subminiature B) connector is a small version of the SMC connector. It was developed in the 1960s and features a snap-on coupling for fast connections. It features a self-centering outer spring and overlapping dielectric. It is rated from 2–4 GHZ, but can possibly work up to 10 GHz.
The MCX (Micro Coax) connector is a coax RF connector developed in the 1980s. It has a snap-on interface and uses the same inner contact and insulator as the SMB connector but is 30% smaller. It can be used in broadband applications up to 6 GHz.
- Pdf Drawing...
Color-Coded Snagless Pre-Plug (Red) PDF Drawing
PDF Drawing for the FMT720
Black Box Explains…Terminating fiber.
Terminating fiber cable used to be a job for experts only. But today, prepolished connectors make it possible for anyone to terminate multimode fiber—all you need is a bit of... more/see it nowpatience and the right tools. Here’s how to terminate fiber with ST connectors:
Step 1 — Slide the connector strain-relief boot, small end first, onto the cable.
Step 2 — Using a template, mark the jacket dimensions to be stripped (40 mm and 52 mm from the end).
Step 3 — Remove the outer jacket from the cable end to the 40 mm mark. Cut the exposed Kevlar. Carefully remove the jacket to the 52-mm mark, exposing the remaining length of Kevlar.
Step 4 — Fan out the Kevlar fibers and slide the crimp ring of the connector approximately 5 mm over the fibers to hold them out of the way. Mark the fiber buffer 11 mm from the end of the cable jacket. Also, mark the buffer where it meets the jacket.
Step 5 — Bit by bit, strip off the buffering until you reach the 11-mm mark. Check the mark you made on the buffer at the jacket. If it’s moved, carefully work the buffer back into the jacket to its original position.
Step 6 — Clean the glass fiber with an alcohol wipe. Cleave the fiber to an 8-mm length.
Step 7 — Carefully insert the fiber into the connector until you feel it bottom out and a bow forms between the connector and the clamp. Cam the connector with the appropriate tool.
Step 8 — Crimp the connector.
Step 9 — Slide the crimp ring up the jacket away from the connector, releasing the Kevlar fibers. Fan the fiber so they encircle the buffer. The ends of the fibers should just touch the rear of the connector—if they’re too long, trim them now.
Step 10 — Crimp the connector again.
Step 11 — Slide the strain-relief boot over the rear of the connector. You might want to put a bead of 411 Loctite adhesive for extra strength on the rear of the boot where it meets the jacket.
Although the details may vary slightly with different connectors and termination kits, the basic termination procedure is the same. collapse
- Pdf Drawing...
CAT5e Modular Plugs, RJ-45
PDF Drawing for the FMTPE-10PAK, FMTPE-25PAK, FMTPE-50PAK, FMTPE-100PAK, and FMTPE-250PAK
- Pdf Drawing...
Color-Coded Snagless Pre-Plug (Brown) PDF Drawing
PDF Drawing for the FMT737
Black Box Explains...PC, UPC, and APC fiber connectors.
Fiber optic cables have different types of mechanical connections. The type of connection determines the quality of the fiber optic lightwave transmission. The different types well discuss here are the... more/see it nowflat-surface, Physical Contact (PC), Ultra Physical Contact (UPC), and Angled Physical Contact (APC).
The original fiber connector is a flat-surface connection, or a flat connector. When mated, an air gap naturally forms between the two surfaces from small imperfections in the flat surfaces. The back reflection in flat connectors is about -14 dB or roughly 4%.
As technology progresses, connections improve. The most common connection now is the PC connector. Physical Contact connectors are just thatthe end faces and fibers of two cables actually touch each other when mated.
In the PC connector, the two fibers meet, as they do with the flat connector, but the end faces are polished to be slightly curved or spherical. This eliminates the air gap and forces the fibers into contact. The back reflection is about -40 dB. This connector is used in most applications.
An improvement to the PC is the UPC connector. The end faces are given an extended polishing for a better surface finish. The back reflection is reduced even more to about -55 dB. These connectors are often used in digital, CATV, and telephony systems.
The latest technology is the APC connector. The end faces are still curved but are angled at an industry-standard eight degrees. This maintains a tight connection, and it reduces back reflection to about -70 dB. These connectors are preferred for CATV and analog systems.
PC and UPC connectors have reliable, low insertion losses. But their back reflection depends on the surface finish of the fiber. The finer the fiber grain structure, the lower the back reflection. And when PC and UPC connectors are continually mated and remated, back reflection degrades at a rate of about 4 to 6 dB every 100 matings for a PC connector. APC connector back reflection does not degrade with repeated matings. collapse