Black Box Explains...Power problems.
The Threat — A sag is a decline in the voltage level. Also known as “brownouts,” sags are the most common power problem.
The Cause — Sags can be caused... more/see it nowlocally by the start-up demands of electrical devices such as motors, compressors, and elevators. Sags may also happen during periods of high electrical use, such as during a heat wave.
The Effect — Sags are often the cause of “unexplained” computer glitches such as system crashes, frozen keyboards, and data loss. Sags can also reduce the efficiency and lifespan of electrical motors.
The Threat — A blackout is a total loss of power.
The Cause — Blackouts are caused by excessive demand on the power grid, an act of nature such as lightning or an earthquake, or a human accident such as a car hitting a power pole or a backhoe digging in the wrong place.
The Effect — Of course a blackout brings everything to a complete stop. You also lose any unsaved data stored in RAM and may even lose the total contents of your hard drive.
The Threat — A spike, also called an impulse, is an instantaneous, dramatic increase in voltage.
The Cause — A spike is usually caused by a nearby lightning strike but may also occur when power is restored after a blackout.
The Effect — A spike can damage or completely destroy electrical components and also cause data loss.
The Threat — A surge is an increase in voltage lasting at least 1/120 of a second.
The Cause — When high-powered equipment such as an air conditioner is powered off, the excess voltage is dissipated though the power line causing a surge.
The Effect — Surges stress delicate electronic components causing them to wear out before their time.
The Threat — Electrical noise, more technically called electromagnetic interference (EMI) and radio frequency interference (RFI), interrupts the smooth sine wave expected from electrical power.
The Cause — Noise has many causes including nearby lightning, load switching, industrial equipment, and radio transmitters. It may be intermittent or chronic.
The Effect — Noise introduces errors into programs and data files. collapse
Telco (Dialup Modem/Fax) RJ-11 Surge Protector Manual
Manual for SP365A-R2 (Version 1)
RS-232 Surge Protector, DB25, 4-Wire Serial Manual
Manual for SP141A (Version 1)
Power over Ethernet Surge Protector, 60-Volt Manual
Manual for SP075A (Version 1)
T1 Non-Span Surge Protector User Manual
User Manual for the SP526A (Version 1)
Black Box Explains...Optical isolation and ground loops.
Optical isolation protects your equipment from dangerous ground loops. A ground loop is a current across a conductor, created by a difference in potential between two grounded points, as in... more/see it nowequipment in two buildings connected by a run of RS-232 or other data line. When two devices are connected and their potentials are different, voltage flows from high to low by traveling through the data cable. If the voltage potential is large enough, your equipment wont be able to handle the excess voltage and one of your ports will be damaged.
Ground loops can also exist in industrial environments. They can be created when power is supplied to your equipment from different transformers or when someone simply turns equipment on and off. Ground loops can also occur when there is a nearby lightning strike. During an electrical storm, the ground at one location can be charged differently than the other location, causing a heavy current flow through the serial communication lines that damage components.
You cant test for ground loops. You dont know you have one until a vital component fails. Only prevention works. For data communication involving copper cable, optical isolation is key.
With optical isolation, electrical data is converted to an optical beam, then back to an electrical pulse. Because there is no electrical connection between the DTE and DCE sides, an optical isolator unlike a surge suppressorwill not pass large sustained power surges through to your equipment. Since data only passes through the optical isolator, your equipment is protected against ground loops and other power surges. collapse
ISDN Data Line Surge Protector, RJ-45, S/T Interface (8-Pin) Manual
Manual for SP060A-R2 (Version 1)
10BASE-T/100BASE-TX In-Line Surge Protector Manual
Manual for SP512A-R3 (Version 1)
Product Data Sheets (pdf)...Special-Application Surge Protectors
- Specification Sheet...
Quick-Connect Surge Protector Spec Sheet
Spec Sheet for SP606A (Version 1)