Loading


Categories (x) > Digital Signage (x)

Results 41-50 of 97 < 1 2 3 4 5 > >> 
  • Video...iCOMPEL™ How-To (Part 7): Set up a publisher and subscriber.

    This video covers setup of the iCOMPEL™ publisher and subscriber units. It begins with an explanation of the function performed by each and discusses what is needed to display unique... more/see it nowcontent on different screens. Next, it shows how to set up a digital signage channel, as well as how to use the iCOMPEL software interface to choose a publishing mode (manual vs. automatic), select a channel server (using the iCOMPEL unit’s channel folder, a USB flash memory folder, or an FTP site), and more. In addition, it explains how to connect a Web browser to a subscriber and how to set up the subscriber so it ”knows” where to pull content from. collapse


DisplayPort cable.

DisplayPort is a digital video interface that was designed by the Video Electronics Standards Association (VESA) in 2006 and has been produced since 2008. It competes directly with HDMI®. Unlike... more/see it nowHDMI, however, DisplayPort is an open standard with no royalties.

This digital interface is used primarily between a computer and a monitor or a high-definition television and is built into many computer chipsets produced today. It’s incredibly versatile, with the capability to deliver digital video, audio, bidirectional communications, and accessory power over a single connector.

DisplayPort v1.1 supports a maximum of 10.8 Gbps over a 2-meter cable; v1.2 supports up to 21.6 Gbps. DisplayPort v1.2 also enables you to daisychain up to four monitors with only a single output cable. It also offers the future promise of DisplayPort Hubs that would operate much like a USB hub.

The standard DisplayPort connector is very compact and features latches that don’t add to the connector’s size. Unlike HDMI, a DisplayPort connector is easily lockable with a pinch-down locking hood, so it can't be easily dislodged. However, a quick squeeze of the connector releases the latch.

DisplayPort supports cable lengths of up to 15 meters with maximum resolutions at cable lengths up to 3 meters. Bidirectional signaling enables DisplayPort to both send and receive data from an attached device.

With the proper adapters, DisplayPort cable can carry DVI and HDMI signals, although this doesn’t work the other way around—DVI and HDMI cable can’t carry DisplayPort. Because DisplayPort can provide power to attached devices, DisplayPort to HDMI or DVI adapters don’t need a separate power supply.

The Mini DisplayPort (MiniDP or mDP) is a miniatured version of the DisplayPort interface. It carries both digital and analog computer video and audio signals. Apple® introduced the Mini DisplayPort connector in 2008 and it is now on all new Mac® computers. It is also being used in newer PC notebooks. This small form factor connector fully supports the VESA DisplayPort protocol. It is particularly useful on systems where space is at a premium, such as laptops, or to support multiple connectors on reduced height add-in cards.

collapse

  • Pdf Drawing... 
  • VGA Splitter Cable PDF Drawing
    PDF Drawing for EVN21VGA (Version 1)
 

Product Data Sheets (pdf)...ICOMPEL O Series Subscriber


Black Box Explains...Digital Visual Interface (DVI) and other digital display interfaces.

There are three main types of digital video interfaces: P&D, DFP, and DVI. P&D (Plug & Display, also known as EVC), the earliest of these technologies, supports both digital and... more/see it nowanalog RGB connections and is now used primarily on projectors. DFP (Digital Flat-Panel Port) was the first digital-only connector on displays and graphics cards; it’s being phased out.

There are different types of DVI connectors: DVI-D, DVI-I, DVI-A, DFP, and EVC.

DVI-D is a digital-only connector. DVI-I supports both digital and analog RGB connections. Some manufacturers are offering the DVI-I connector type on their products instead of separate analog and digital connectors. DVI-A is used to carry an analog DVI signal to a VGA device, such as a display. DFP, like DVI-D, was an early digital-only connector used on some displays; it’s being phased out. EVC (also known as P&D) is similar to DVI-I only it’s slightly larger in size. It also handles digital and analog connections, and it’s used primarily on projectors.

All these standards are based on transition-minimized differential signaling (TMDS). In a typical single-line digital signal, voltage is raised to a high level and decreased to a low level to create transitions that convey data. TMDS uses a pair of signal wires to minimize the number of transitions needed to transfer data. When one wire goes to a high-voltage state, the other goes to a low-voltage state. This balance increases the data-transfer rate and improves accuracy. collapse


Product Data Sheets (pdf)...MediaFlyer EXPRESS Digital Signage


Product Data Sheets (pdf)...iCOMPEL™ Black Box Digital Signage


Black Box Explains: M1 connectors.

In 2001, the Video Electronics Standards Association (VESA) approved the M1 Display Interface System for digital displays. The M1 system is a versatile and convenient system designed for computer displays,... more/see it nowspecifically digital projectors. M1 supports both analog and digital signals.

M1 is basically a modified DVI connector that can support DVI, VGA, USB and IEEE-1394 signals. The single connector replaces multiple connectors on projectors. An M1 cable can also be used to power accessories, such as interface cards for PDAs.

There are three primary types of M1 connectors:
–M1-DA (digital and analog). This is the most common connector, and it supports VGA, USB and DVI signals.
–M1-D (digital) supports DVI signals.
–M1-A (analog) supports VGA signals.

The M1 standard does not cover any signal specifications or detailed connector specifications. collapse


Black Box Explains...Digital Visual Interface (DVI) cables.

The Digital Visual Interface (DVI) standard is based on transition-minimized differential signaling (TMDS). In a typical single-line digital signal, voltage is raised to a high level and decreased to a... more/see it nowlow level to create transitions that convey data. To minimize the number of transitions needed to transfer data, TMDS uses a pair of signal wires. When one wire goes to a high-voltage state, the other goes to a low-voltage state. This balance increases the data-transfer rate and improves accuracy.

There are different types of DVI connectors: DVI-D, DVI-I, DVI-A, DFP, and EVC. DVI-D is a digital-only connector.

DVI-D is a digital-only connector. DVI-I supports both digital and analog RGB connections. Some manufacturers are offering the DVI-I connector type on their products instead of separate analog and digital connectors. DVI-A is used to carry an analog DVI signal to a VGA device, such as a display. DFP, like DVI-D, was an early digital-only connector used on some displays; it’s being phased out. EVC (also known as P&D) is similar to DVI-I only it’s slightly larger in size. It also handles digital and analog connections, and it’s used primarily on projectors. collapse


Black Box Explains... Speaker wire gauge.

Wire gauge (often shown as AWG, for American Wire Gauge) is a measure of the thickness of the wire. The more a wire is drawn or sized, the smaller its... more/see it nowdiameter will be. The lower the wire gauge, the thicker the wire.

For example, a 24 AWG wire is thinner than a 14 AWG wire. A lower AWG means longer transmission distance and better integrity. As a rule of thumb, power loss decreases as the wire size increases.

When it comes to choosing speaker cable, consider a few factors: distance, the type of system and amplifier you have, the frequencies of the signals being handled, and any specifications that the speaker manufacturer recommends.

For most home applications where you simply need to run cable from your stereo to speakers in the same room—or even behind the walls to other rooms—16 AWG cable is usually fine.

If you’re considering runs of more than 40 feet (12.1 m), consider using 14 AWG or even 12 AWG cable. They both offer better transmission and less resistance over longer distances. You should probably choose 12 AWG cable for high-end audio systems with higher power output or for low-frequency subwoofers. As a rule of thumb, power loss decreases as the wire size increases.

To terminate your cable, choose gold connectors. Because gold resists oxidation over time, gold connectors wear better and offer better peformance than other connectors do. collapse

Results 41-50 of 97 < 1 2 3 4 5 > >> 
Close

Support

Delivering superior technical support is our highest priority. Depending on the products or services we provide for you, please visit your appropriate support area.



 
Print
Black Box 1-877-877-2269 Black Box Network Services