Black Box Explains...How a line driver operates.
Driving data? Better check the transmission.
Line drivers can operate in any of four transmission modes: 4-wire full-duplex, 2-wire full-duplex, 4-wire half-duplex, and 2-wire half-duplex. In fact, most models support more... more/see it nowthan one type of operation.
So how do you know which line driver to use in your application?
The deal with duplexing.
First you must decide if you need half- or full-duplex transmission. In half-duplex transmission, voice or data signals are transmitted in only one direction at a time, as in a CB radio conversation. In full-duplex operation, voice or data signals are transmitted in both directions at the same time, as in a telephone conversation.
The entire bandwidth is available for your transmission in half-duplex mode. In full-duplex mode, however, the bandwidth must be split in two because data travels in both directions simultaneously.
Two wires or not two wires? That is the question.
The second consideration you have is the type of twisted-pair cable you need to complete your data transmissions. Generally you need twisted-pair cable with either two or four wires. Often the type of cabling that’s already installed in a building dictates what kind of a line driver you use. For example, if two twisted pairs of UTP cabling are available, you can use a line driver that operates in 4-wire applications, such as the Short-Haul Modem-B Async or the Line Driver-Dual Handshake models. Otherwise, you might choose a line driver that works for 2-wire applications, such as the Short-Haul Modem-B 2W or the Async 2-Wire Short-Haul Modem.
If you have the capabilities to support both 2- and 4-wire operation in half- or full-duplex mode, we even offer line drivers that support all four types of operation.
As always, if you’re still unsure which operational mode will work for your particular applications, consult our Technical Support experts and they’ll help you make your decision. collapse
Black Box Explains...Benefits of T1 and E1.
If you manage a heavy-traffic data network and you demand high bandwidth for high speeds, Black Box has what you need to send your data digitally over super-fast T1 or... more/see it nowE1 communication lines.
Both T1 and E1 are foundations of global voice communication.
Developed more than 30 years ago and commercially available since 1983, T1 and E1 go virtually anywhere phone lines go, but faster.
T1 sends data up to 1.544 Mbps. E1 supports speeds to 2.048 Mbps. No matter where you need to connect—North, South, or Central America, Europe, or the Pacific Rim—T1 and E1 can get your data there—fast!
Both services provide flexibility for a multitude of applications.
Whether you need to drive a private, point-to-point line or a high-speed circuit; provide corporate access to the Internet or inbound access to your own webserver; or support a voice/data/fax/video WAN that extends halfway around the world, T1 or E1 can make the connection.
Both offer cost-effective connections.
In recent years, competition among telco service providers has led to increasingly more affordable prices for T1 and E1 services. In fact, most companies seriously considering a shift to T1 or E1 find they can negotiate even better rates with just a little comparative cost analysis.
• Trunking of V.90 and ISDN remote connection to a central location.
• Accessing public Frame Relay networks for voice, fax, and data.
• Merging voice and data traffic. A single T1 or E1 line can give you several additional voice and data lines at no additional cost.
• Making LAN connections. If you’re linking LANs, a T1 or E1 line offers excellent performance.
• Sending bandwidth-intensive data such as CAD/CAM, MRI, CAT-scan images, and other graphics with large files. collapse
Black Box Explains...DDS vs. T1.
DDS (Digital Data Service) is an AT&T® service that transmits data digitally over dedicated leased lines. DDS lines use four wires, and support speeds up to 56 kbps; however, DDS... more/see it nowis actually a 64-kbps circuit with 8 kbps being used for signaling. You can also get 64-kbps (ClearChannel™) service. Since the transmission is digital, no modems are needed. Dedicated digital lines are ideal for point-to-point links in wide-area networks.
T1 is a dedicated transmission line operating at 1.544 Mbps. It’s comprised of 24 DSOs, each supporting speeds of 64 kbps. The user sends data at N x 56 or N x 64 over T1 circuits. T1 operates over twisted-pair cable and is suitable for voice, data, and image transmissions on long-distance networks. collapse
Black Box Explains...Modem eliminators.
Understanding the process of elimination.
If your office environment has sync equipment, and if that equipment is also used for local data communications, you should consider replacing those modems with cost-effective... more/see it nowand versatile modem eliminators.
What does a modem eliminator do?
One modem eliminator can connect a local terminal and computer port in lieu of the pair of modems that they would normally connect to. Plus, a modem eliminator enables DCE-to-DTE data and control-signal connections that are not easily achieved by standard cables or connectors in a sync environment.
Basically, a modem eliminator simulates a sync data link. It does this two ways. First, it provides clocking, which is mandatory for sync devices to communicate. Second, it provides the handshaking that DCEs do.
Why should you use a modem eliminator?
One—if you have two sync DTEs in the same room or close to each other, you will need a modem eliminator.
Two—if you have a network with routers, you just found the perfect equipment tester.
A modem eliminator can enable in-house bench testing of routers or existing equipment. Theres no need to place routers all over your network only to find out they don’t work once you test the LAN. A modem eliminator tells you what equipment passes your tests before you install.
Three—a modem eliminator makes good economic sense. One does the job of two modems—and it does the job better. You get a high return on your investment. collapse
Black Box Explains...DS-3 and DS-4
Digital signal (DS) speeds are used to classify the capacities of lines and trunks as designated by the Trunk (T) carrier systems. The most well-known T carrier system is the... more/see it nowNorth American T1 standard, which was originally designed to transmit digitized voice signals at 1.544 Mbps (DS-1). T carrier systems now carry digital data as well as voice transmissions.
DS-3 lines offer the functional equivalent of 28 T1 channels, operating at 44.736 Mbps (commonly rounded up to 45 Mbps). These lines handle up to 672 voice conversations and are used in high-speed interconnect and DS cross-connect (DSX) applications.
DS-4 offers 274.176 Mbps transmission—the same as 4032 standard voice channels—and has 168 times the capacity of T1. This performance level is generally used for carrier backbone networks.
Products offering DS-3 and DS-4 functionality comply with T3 and T4 standards, respectively, and with Bellcore GR-139-CORE specifications. collapse
Black Box Explains...Beyond T1—other standards for high-speed circuits.
While there are many applications for basic T1 rate service (1.536 Mbps), some applications require much more bandwidth. One of the most attractive features of T1 is the number of... more/see it nowoptions available to accommodate these kinds of demands. The important thing to remember is that all of these higher-speed services operate with the same consistent framing formats as the standard T1 service.
T1 is a high-speed service with a clock speed of 1.544 Mbps. It’s made up of 24 64-kbps DS0 (Digital-Signal [zero]) subchannels that together can support throughput rates of up to 1.536 Mbps. But there are higher levels of T1 service that are also available. For instance, T1C service doubles the T1 rate. It supports 3.152 Mbps with a total of 48 DS0s for top-speed applications. In a T1C environment, two T1 lines are combined into one using a special T1 mux.
The next-highest level of service is called T2. It offers 6.312 Mbps over 96 DS0s by multi-plexing 4 T1 lines into a single high-speed line.
The next two levels of service are exponentially larger than T2. A high-speed T3 trunk line is 28 times larger than a standard T1 line. T3 brings 44.736 Mbps to a customer site via 672 DS0s. This tremendous capacity is made possible by multiplexing 28 T1 lines or combina?tions of T2 and T1 lines.
Finally, T4 service offers a bandwidth potential of 274.176 Mbps, made up of 4032 64-kbps DS0 subchannels. At 168 times the size of a standard 1.544-Mbps line, T4 service dwarfs T1. The physical connections require multiplexing 6 T3 lines or 168 T1 lines into a single high-speed trunk.
With so many incredibly high-speed T-level service options available, system administrators have great flexibility to configure their operations for maximum efficiency and economy.
It’s important to remember that these various levels of T1 services can be implemented simultaneously within a particularly large enterprise to support complex network configurations.
Of course, this kind of application has the potential to become somewhat overwhelming from a management standpoint. However, as long as you keep track of the individual DS0s, you should always be able to accurately gauge how much available bandwidth you have at your disposal. collapse
Black Box Explains...How MicroRACK Cards fit together.
Slide a function card into the front of the rack. Then slide a connector card in from the back. The rest is simple. Just press the cards together firmly inside... more/see it nowthe rack to seat the connectors.
Changing systems? Its easy to change to a different connector card. Just contact us, and well find the right connection for you.
Add a hot-swappable power supply (AC for normal operation, VDC for battery-powered sites), and youre up and running. collapse
Black Box Explains... Advantages of the MicroRACK system.
• Midplane architecture—Separate front and rear cards make changing interfaces easy.
• Multiple functions—Supports line drivers, interface converters, fiber modems, CSU/DSUs, and synchronous modem eliminators.
• Hot swappable—MicroRACK Cards can be replaced... more/see it nowwithout powering down, so you cut your networks downtime.
• Two-, four-, and eight-port MicroRACKs—available for smaller or desktop installations. Theyre just right for tight spaces that cant accommodate a full-sized (16-port) rack.
• Optional dual cards—Some Mini Driver Cards have two drivers in one card. One MicroRACK chassis can hold up to 32 Mini Drivers!
• All standard connections available—DB25, RJ-11, RJ-45, fiber, V.35.
• Choose you own power supply—120240 VAC, 12 VDC, 24 VDC, or 48 VDC. collapse